View MC78M15ACDT_2960433.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

device operating temperature range package semiconductor technical data threeterminal medium current positive fixed voltage regulators ordering information mc78mxxcdt mc78mxxct t j = 40 to +125 c dpak to220 order this document by mc78m00/d mc78mxxacdt* xx indicates nominal voltage. * available in 5.0, 8.0, 12 and 15 v devices. dt1 suffix plastic package case 369 (dpak) dt suffix plastic package case 369a (dpak) pin 1. input 2. ground 3. output t suffix plastic package case 221a (to220) heatsink surface connected to pin 2. heatsink surface (shown as terminal 4 in case outline drawing) is connected to pin 2. 3 1 2 3 1 mc78mxxact* 3 1 2 1 motorola analog ic device data
the mc78m00/mc78m00a series positive voltage regulators are identical to the popular mc7800 series devices, except that they are specified for only half the output current. like the mc7800 devices, the mc78m00 threeterminal regulators are intended for local, oncard voltage regulation. internal current limiting, thermal shutdown circuitry and safearea compensation for the internal pass transistor combine to make these devices remarkably rugged under most operating conditions. maximum output current, with adequate heatsinking is 500 ma. ? no external components required ? internal thermal overload protection ? internal short circuit current limiting ? output transistor safearea compensation ? mc78m00a high accuracy ( 2%) available for 5.0 v, 8.0 v, 12 v and 15 v ? previous commerical temperature range has been extended to a junction temperature range of 40 c to +125 c representative schematic diagram this device contains 28 active transistors. 1.0 k 1.0 k input 210 6.7 v 16 k 100 200 300 3.6 k 6.4 k 520 6.0 k 2.0 k 3.9 k 6.0 k 2.8 k 40 pf 5.6 k 3.0 k 1.0 k 300 200 50 13 0.24 gnd output 10 pf 2.6 k device type/nominal output voltage mc78m05ac 5.0 v mc78m09c 9.0 v mc78m18c 18 v mc78m05c 5.0 v mc78m12ac 12 v mc78m20c 20 v mc78m06c 6.0 v mc78m12c 12 v mc78m24c 24 v mc78m08ac 8.0 v mc78m15ac 15 v mc78m08c 8.0 v mc78m15c 15 v ? motorola, inc. 1997 rev 6
mc78m00 mc78m00a series 2 motorola analog ic device data maximum ratings (t a = 25 c, unless otherwise noted.) rating symbol value unit input voltage (5.0 v18 v) v i 35 vdc (20 v24v) 40 power dissipation (package limitation) plastic package, t suffix t a = 25 c p d internally limited thermal resistance, junctiontoair q ja 70 c/w thermal resistance, junctiontocase q jc 5.0 c/w plastic package, dt suffix t a = 25 c p d internally limited thermal resistance, junctiontoair q ja 92 c/w thermal resistance, junctiontocase q jc 5.0 c/w operating junction temperature range t j +150 c storage temperature range t stg 65 to +150 c note: esd data available upon request. mc78m05c/ac electrical characteristics (v i = 10 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o vdc mc78m05c 4.8 5.0 5.2 mc78m05ac 4.9 5.0 5.1 output voltage variation v o vdc (7.0 vdc v i 20 vdc, 5.0 ma i o 350 ma) mc78m05c 4.75 5.25 mc78m05ac 4.80 5.20 line regulation reg line 3.0 5.0 mv (t j = 25 c, 7.0 vdc v i 25 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 200 ma) 20 100 (t j = 25 c, 5.0 ma i o 500 ma) 10 50 input bias current (t j = 25 c) i ib 3.2 6.0 ma quiescent current change d i ib ma (8.0 vdc v i 25 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 40 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 8.0 v v i 18 v) 62 (i o = 300 ma, f = 120 hz, 8.0 v i 18 v, t j = 25 c) 62 80 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.2 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c)
mc78m00 mc78m00a series 3 motorola analog ic device data mc78m06c electrical characteristics (v i = 11 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o 5.75 6.0 6.25 vdc output voltage variation v o 5.7 6.3 vdc (8.0 vdc v i 21 vdc, 5.0 ma i o 350 ma) line regulation reg line 5.0 50 mv (t j = 25 c, 8.0 vdc v i 25 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 20 120 (t j = 25 c, 5.0 ma i o 200 ma) 10 60 input bias current (t j = 25 c) i ib 3.2 6.0 ma quiescent current change d i ib ma (9.0 vdc v i 25 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 45 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 9.0 v v i 19 v) 59 (i o = 300 ma, f = 120 hz, 9.0 v v i 19 v, t j = 25 c) 59 80 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.2 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c) mc78m08c/ac electrical characteristics (v i = 14 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o vdc mc78m08c 7.70 8.0 8.30 mc78m08ac 7.84 8.0 8.16 output voltage variation v o vdc (10.5 vdc v i 23 vdc, 5.0 ma i o 350 ma) mc78m08c 7.6 8.4 mc78m08ac 7.7 8.3 line regulation reg line 6.0 50 mv (t j = 25 c, 10.5 vdc v i 25 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 25 160 (t j = 25 c, 5.0 ma i o 200 ma) 10 80 input bias current (t j = 25 c) i ib 3.2 6.0 ma quiescent current change d i ib ma (10.5 vdc v i 25 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 52 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 11.5 v v i 21.5 v) 56 (i o = 300 ma, f = 120 hz, 11.5 v v i 21.5 v, t j = 25 c) 56 80 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.2 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c)
mc78m00 mc78m00a series 4 motorola analog ic device data mc78m09c electrical characteristics (v i = 15 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o 8.64 9.0 9.45 vdc output voltage variation v o 8.55 9.45 vdc (11.5 vdc v i 23 vdc, 5.0 ma i o 350 ma) line regulation reg line 6.0 50 mv (t j = 25 c, 11.5 vdc v i 25 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 25 180 (t j = 25 c, 5.0 ma i o 200 ma) 10 90 input bias current (t j = 25 c) i ib 3.2 6.0 ma quiescent current change d i ib ma (11.5 vdc v i 25 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 52 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 12.5 v v i 22.5 v) 56 (i o = 300 ma, f = 120 hz, 12.5 v v i 22.5 v, t j = 25 c) 56 80 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.2 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c) mc78m12c/ac electrical characteristics (v i = 19 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o vdc mc78m12c 11.50 12 12.50 mc78m12ac 11.76 12 12.24 output voltage variation v o vdc (14.5 vdc v i 27 vdc, 5.0 ma i o 350 ma) mc78m12c 11.4 12.6 mc78m12ac 11.5 12.5 line regulation reg line 8.0 50 mv (t j = 25 c, 14.5 vdc v i 30 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 25 240 (t j = 25 c, 5.0 ma i o 200 ma) 10 120 input bias current (t j = 25 c) i ib 3.2 6.0 ma quiescent current change d i ib ma (14.5 vdc v i 30 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 75 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 15 v v i 25 v) 55 (i o = 300 ma, f = 120 hz, 15 v v i 25 v, t j = 25 c) 55 80 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.3 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c)
mc78m00 mc78m00a series 5 motorola analog ic device data mc78m15c/ac electrical characteristics (v i = 23 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o vdc mc78m15c 14.4 15 15.6 mc78m15ac 14.7 15 15.3 output voltage variation v o vdc (17.5 vdc v i 30 vdc, 5.0 ma i o 350 ma) mc78m15c 14.25 15.75 mc78m15ac 14.40 15.60 input regulation reg line 10 50 mv (t j = 25 c, 17.5 vdc v i 30 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 25 300 (t j = 25 c, 5.0 ma i o 200 ma) 10 150 input bias current (t j = 25 c) i ib 3.2 6.0 ma quiescent current change d i ib ma (17.5 vdc v i 30 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 90 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 18.5 v v i 28.5 v) 54 (i o = 300 ma, f = 120 hz, 18.5 v v i 28.5 v, t j = 25 c) 54 70 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.3 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c) mc78m18c electrical characteristics (v i = 27 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o 17.3 18 18.7 vdc output voltage variation v o 17.1 18.9 vdc (21 vdc v i 33 vdc, 5.0 ma i o 350 ma) line regulation reg line 10 50 mv (t j = 25 c, 21 vdc v i 33 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 30 360 (t j = 25 c, 5.0 ma i o 200 ma) 10 180 input bias current (t j = 25 c) i ib 3.2 6.5 ma quiescent current change d i ib ma (21 vdc v i 33 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 100 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 22 v v i 32 v) 53 (i o = 300 ma, f = 120 hz, 22 v v i 32 v, t j = 25 c) 53 70 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.3 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c)
mc78m00 mc78m00a series 6 motorola analog ic device data mc78m20c electrical characteristics (v i = 29 v, i o = 350 ma, 30 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o 19.2 20 20.8 vdc output voltage variation v o 19 21 vdc (23 vdc v i 35 vdc, 5.0 ma i o 350 ma) line regulation reg line 10 50 mv (t j = 25 c, 23 vdc v i 35 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 30 400 (t j = 25 c, 5.0 ma i o 200 ma) 10 200 input bias current (t j = 25 c) i ib 3.2 6.5 ma quiescent current change d i ib ma (23 vdc v i 35 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 110 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 24 v v i 34 v) 52 (i o = 300 ma, f = 120 hz, 24 v v i 34 v, t j = 25 c) 52 70 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c, v i = 35 v) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.5 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c) mc78m24c electrical characteristics (v i = 33 v, i o = 350 ma, 40 c < t j < 125 c, p d 5.0 w, unless otherwise noted.) characteristics symbol min typ max unit output voltage (t j = 25 c) v o 23 24 25 vdc output voltage variation v o 22.8 25.2 vdc (27 vdc v i 38 vdc, 5.0 ma i o 350 ma) line regulation reg line 10 50 mv (t j = 25 c, 27 vdc v i 38 vdc, i o = 200 ma) load regulation reg load mv (t j = 25 c, 5.0 ma i o 500 ma) 30 480 (t j = 25 c, 5.0 ma i o 200 ma) 10 240 input bias current (t j = 25 c) i ib 3.2 7.0 ma quiescent current change d i ib ma (27 vdc v i 38 vdc, i o = 200 ma) 0.8 (5.0 ma i o 350 ma) 0.5 output noise voltage (t a = 25 c, 10 hz f 100 khz) v n 170 m v ripple rejection rr db (i o = 100 ma, f = 120 hz, 28 v v i 38 v) 50 (i o = 300 ma, f = 120 hz, 28 v v i 38 v, t j = 25 c) 50 70 dropout voltage v i v o 2.0 vdc (t j = 25 c) short circuit current limit (t j = 25 c) i os 50 ma average temperature coefficient of output voltage d v o / d t 0.5 mv/ c (i o = 5.0 ma) peak output current i o 700 ma (t j = 25 c)
mc78m00 mc78m00a series 7 motorola analog ic device data definitions line regulation the change in output voltage for a change in the input voltage. the measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. load regulation the change in output voltage for a change in load current at constant chip temperature. maximum power dissipation the maximum total device dissipation for which the regulator will operate within specifications. input bias current that part of the input current that is not delivered to the load. output noise voltage the rms ac voltage at the output, with constant load and no input ripple, measured over a specified frequency range. long term stability output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices' electrical characteristics and maximum power dissipation. figure 1. dpak thermal resistance and maximum power dissipation versus p.c.b. copper length figure 2. worst case power dissipation versus ambient temperature (to220) , power dissipation (w) d p q jc = 5 c/w p d(max) = 7.52 w no heat sink q hs = 20 c/w q hs = 10 c/w infinite heat sink r , thermal resistance ja q junctiontoair ( c/w) l, length of copper (mm) p d , maximum power dissipation (w) r q ja 10 5.0 3.0 2.0 1.0 0.5 0.3 0.2 0.1 40 50 60 70 80 90 100 t a , ambient temperature ( c) 25 50 75 100 125 150 0 102030 25 15 5.0 l l free air mounted vertically 2.0 oz. copper p d(max) for t a = 50 c ??? ??? ??? ??? 0 0.4 0.8 1.2 1.6 2.0 2.4 minimum size pad
mc78m00 mc78m00a series 8 motorola analog ic device data t j = 25 c figure 3. peak output current versus dropout voltage figure 4. dropout voltage versus junction temperature figure 5. ripple rejection versus frequency figure 6. ripple rejection versus output current figure 7. bias current versus input voltage 100 80 60 40 20 1.0 10 100 1.0 k 10 k 100 k 1.0 m 10 m 100 m f, frequency (hz) rr, ripple rejection (db) i out = 500 ma , dropout voltage (v) io t j , junction temperature ( c) 2.5 2.0 1.5 1.0 0.5 0 0 25 50 75 100 125 150 v v d v o = 100 mv i o = 500 ma i o = 100 ma i o = 10 ma rr, ripple rejection (db) i o , output current (a) 100 80 60 40 30 0.01 0.1 0.5 1.0 10 v out = 5.0 v v in = 10 v c o = 0 f = 120 hz t j = 25 c , bias current (ma) b v i , input voltage (vdc) 4.0 3.0 2.0 1.0 0 0 5.0 10 15 20 25 30 35 40 i t j = 25 c t j = 125 c t j = 125 c t j = 25 c v o = 5.0 v i o = 0.5 a i o , output current (a) 5.0 4.0 3.0 2.0 1.0 0 0.01 0.1 0.5 1.0 10 t j = 125 c v i v o = 5.0 v figure 8. bias current versus output current , output current (a) o v i v o , dropout voltage (v) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 5.0 10 15 20 25 30 35 40 t j = 125 c t j = 25 c i , bias current (ma) b i i out = 500 ma v out = 5.0 v v in = 10 v c o = 0 t j = 25 c
mc78m00 mc78m00a series 9 motorola analog ic device data applications information design considerations the mc78m00/mc78m00a series of fixed voltage regulators are designed with thermal overload protection that shuts down the circuit when subjected to an excessive power overload condition, internal short circuit protection that limits the maximum current the circuit will pass, and output transistor safearea compensation that reduces the output short circuit current as the voltage across the pass transistor is increased. in many low current applications, compensation capacitors are not required. however, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. an input bypass capacitor should be selected to provide good high frequency characteristics to insure stable operation under all load conditions. a 0.33 m f or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. the bypass capacitor should be mounted with the shortest possible leads directly across the regulator's input terminals. normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. figure 9. current regulator figure 10. adjustable output regulator figure 11. current boost regulator figure 12. current boost with short circuit protection the mc78m00 regulators can also be used as a current source when connected as above. in order to minimize dissipation the mc78m05c is chosen in this application. resistor r determines the current as follows: for example, a 500 ma current source would require r to be a 5.0 w , 10 w resistor and the output voltage compliance would be the input voltage less 7.0 v. i o = 5.0 v r + i ib i ib = 1.5 ma over line and load changes. input 0.33 m f r i o mc78m05c constant current to grounded load the addition of an operational amplifier allows adjustment to higher or intermediate values while retaining regulation characteristics. the minimum voltage obtainable with this arrangement is 2.0 v greater than the regulator voltage. input mc78m05c output 0.33 m f 10 k mc1741 7 6 4 1.0 k 0.1 m f 3 2 the mc78m00 series can be current boosted with a pnp transistor. the mj2955 provides current to 5.0 a. resistor r in conjunction with the v be of the pnp determines when the pass transistor begins conducting; this circuit is not short circuit proof. inputoutput differential voltage minimum is increased by v be of the pass transistor. xx = 2 digits of type number indicating voltage. mc78mxxc input output r 1.0 m f mj2955 or equiv. 1.0 m f the circuit of figure no tag can be modified to provide supply protection against short circuits by adding a short circuit sense resistor, r sc , and an additional pnp transistor. the current sensing pnp must be able to handle the short circuit current of the threeterminal regulator .therefore, a 4.0 a plastic power transistor is specified. xx = 2 digits of type number indicating voltage. 1.0 m f mc78mxxc mj2955 or equiv. input output r sc r 2n6049 or equiv. v o , 7.0 v to 20 v v in v out 2.0 v +
mc78m00 mc78m00a series 10 motorola analog ic device data t suffix plastic package case 221a06 (to220) issue y dt suffix plastic package case 369a13 (dpak) issue y outline dimensions notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension z defines a zone where all body and lead irregularities are allowed. dim min max min max millimeters inches a 0.570 0.620 14.48 15.75 b 0.380 0.405 9.66 10.28 c 0.160 0.190 4.07 4.82 d 0.025 0.035 0.64 0.88 f 0.142 0.147 3.61 3.73 g 0.095 0.105 2.42 2.66 h 0.110 0.155 2.80 3.93 j 0.018 0.025 0.46 0.64 k 0.500 0.562 12.70 14.27 l 0.045 0.060 1.15 1.52 n 0.190 0.210 4.83 5.33 q 0.100 0.120 2.54 3.04 r 0.080 0.110 2.04 2.79 s 0.045 0.055 1.15 1.39 t 0.235 0.255 5.97 6.47 u 0.000 0.050 0.00 1.27 v 0.045 1.15 z 0.080 2.04 b q h z l v g n a k f 123 4 d seating plane t c s t u r j d a k b r v s f l g 2 pl m 0.13 (0.005) t e c u j h t seating plane z dim min max min max millimeters inches a 0.235 0.250 5.97 6.35 b 0.250 0.265 6.35 6.73 c 0.086 0.094 2.19 2.38 d 0.027 0.035 0.69 0.88 e 0.033 0.040 0.84 1.01 f 0.037 0.047 0.94 1.19 g 0.180 bsc 4.58 bsc h 0.034 0.040 0.87 1.01 j 0.018 0.023 0.46 0.58 k 0.102 0.114 2.60 2.89 l 0.090 bsc 2.29 bsc r 0.175 0.215 4.45 5.46 s 0.020 0.050 0.51 1.27 u 0.020 0.51 v 0.030 0.050 0.77 1.27 z 0.138 3.51 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 123 4
mc78m00 mc78m00a series 11 motorola analog ic device data outline dimensions dt1 suffix plastic package case 36907 (dpak) issue l notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 123 4 v s a k t seating plane r b f g d 3 pl m 0.13 (0.005) t c e j h dim min max min max millimeters inches a 0.235 0.250 5.97 6.35 b 0.250 0.265 6.35 6.73 c 0.086 0.094 2.19 2.38 d 0.027 0.035 0.69 0.88 e 0.033 0.040 0.84 1.01 f 0.037 0.047 0.94 1.19 g 0.090 bsc 2.29 bsc h 0.034 0.040 0.87 1.01 j 0.018 0.023 0.46 0.58 k 0.350 0.380 8.89 9.65 r 0.175 0.215 4.45 5.46 s 0.050 0.090 1.27 2.28 v 0.030 0.050 0.77 1.27
mc78m00 mc78m00a series 12 motorola analog ic device data motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. atypicalo parameters which may be provided in motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur. should buyer purchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that motorola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/affirmative action employer. mfax is a trademark of motorola, inc. how to reach us: usa / europe / locations not listed : motorola literature distribution; japan : nippon motorola ltd.: spd, strategic planning office, 4321, p.o. box 5405, denver, colorado 80217. 13036752140 or 18004412447 nishigotanda, shinagawaku, tokyo 141, japan. 81354878488 customer focus center: 18005216274 mfax ? : rmfax0@email.sps.mot.com touchtone 1 6022446609 asia / pacific : motorola semiconductors h.k. ltd.; 8b tai ping industrial park, motorola fax back system us & canada only 18007741848 51 ting kok road, tai po, n.t., hong kong. 85226629298 http://sps.motorola.com/mfax/ home page : http://motorola.com/sps/ mc78m00/d ?

▲Up To Search▲

Price & Availability of MC78M15ACDT

	To Download MC78M15ACDT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .